GS Light logo

Food Processing Lighting

Food processing lighting has to survive daily washdowns, keep glass away from exposed food and give enough light for inspection, so fixtures are chosen by washdown rating, lens material and the certificate for each model.

Food processing facilities, cold storage warehouses, and food and beverage plants need lighting that withstands high pressure washdowns and supports sanitation audits. GS LIGHT's IP69K high bays and tri proof lights combine washdown rated housings with polycarbonate lens options; ask for the datasheet and certificates of the exact model quoted.
food-lamp

Why LED Lighting Matters in Food Processing Facilities

Steam, grease, temperature swings and repeated hose downs shorten the life of luminaires that are not built for them. Fixtures for food processing use sealed housings, shatter resistant lenses and materials chosen for daily sanitation, with the washdown and chemical exposure checked for each model.

The light levels a plant must meet depend on where it operates and what it produces. In the United States, the FDA Food Code (section 6-303.11) sets minimums for retail and food service: 540 lux (50 foot candles) where staff work with food or with knives, slicers and saws; 215 lux (20 foot candles) inside reach in equipment and at handwashing, warewashing and toilet areas; and 108 lux (10 foot candles) in walk in refrigerators and dry storage. Processing plants fall under 21 CFR 117.20, which requires adequate lighting and shatter resistant fixtures or other protection wherever food is exposed, and many use the Food Code values as a benchmark. In the European Union, Regulation (EC) No 852/2004 requires adequate lighting in food premises and EN 12464-1 gives task values for food industry work areas, while food safety schemes such as BRCGS and IFS add glass and brittle plastic controls. Coolers and freezers have their own considerations, covered on our cold storage lighting page.

Higher Productivity

Inspection and grading need enough light on the product and good color rendering to show defects, discoloration and foreign matter. CRI 80 is a common baseline, and color grading may call for CRI 90 and a color temperature agreed with the quality team, checked with real product under the proposed light.

Inspection tables gain the most: light the grading surface to the level the applicable code or customer standard sets, and add vertical light along conveyors so the sides of the product are visible.
IP65 LED tri proof light

Safer Environment

Sharp tools, wet floors, and moving forklifts make food processing operations dangerous. Clear, even illumination helps workers see wet floors, tools and moving vehicles. Loading docks and dispatch areas follow the same rules as warehouse lighting.

In cold storage and freezer areas, LEDs reach full output when switched on, without the slow start of fluorescent tubes in the cold, provided the model is rated for the room temperature. Check the operating range on the datasheet of the model quoted before it goes into a freezer.
ip69k-tri-proof-light-detail-1

Choosing Fixtures by Plant Area

Choose food plant lighting by area: the washdown method, temperature, chemicals and whether food is exposed decide the housing, lens and rating before wattage does.
Plant area Conditions to check Configuration direction to verify
Wet processing and washdown zones Washdown pressure and temperature, cleaning chemicals, exposed food IP69K rated housings with polycarbonate lenses; gasket and housing chemical resistance confirmed per model
Inspection, grading and QA Light on the product, color judgment, reflections from wet surfaces Higher light on the work surface, CRI 90 where color is graded, vertical light along conveyors
Packaging and dry processing Dust, open packaging, ceiling height Sealed linear or high bay fixtures; polycarbonate where product is exposed
Coolers, freezers and blast freezers Operating temperature, condensation, door openings Models rated for the room temperature; see the cold storage guidance
Ovens, fryers and hot zones Ambient temperature at mounting height, steam, grease The model's rated ambient temperature (Ta) checked against the measured air temperature
Areas with ammonia or strong chemicals Ammonia refrigeration leaks, acids, alkalis Chemical resistant versions; borosilicate glass only where the plant's glass policy allows it and food is not exposed
Loading docks and dispatch Vehicles, weather at open doors, mixed temperatures Washdown or weather rated fixtures as for warehouse docks
The plant's food safety team sets the glass and brittle plastic policy and the light levels, GS LIGHT confirms what each model is rated for, and a photometric calculation sets the layout.

LED Lighting for Washdown and Harsh Conditions

Two fixture types cover most food processing lighting needs: LED high bay lights for open processing floors and IP69K tri proof linear luminaires for aisles, coolers and processing lines. Certification is model specific: GS LIGHT sells a high bay under the name "NSF High Bay Light", and buyers who need NSF should ask for the NSF listing of the exact model quoted. The IP69K rating on both types covers dust and high pressure, high temperature water, not food safety. GS LIGHT recommends suitable configurations and provides product quotations and the available technical documents; the lighting design and installation are handled by the project's appointed professionals.

IP69K LED High Bay Light

GS LIGHT's IP69K high bay lights for food processing use die cast aluminum housings with one piece polycarbonate lens options and 0 to 10V, DALI or DMX512 control by configuration. Wattage, efficacy and the operating temperature range are stated on the datasheet of the version quoted, and an emergency kit is available as an option, while escape route lighting is designed and tested as its own system.

The IP69K rating means the fixture is tested against high pressure, high temperature water jets, the kind used in commercial sanitation; it is a washdown rating, not a food safety certification. Versions with a one piece polycarbonate lens have no glass and no visible screws on the lens side, and rated life is stated on the datasheet with its test conditions.

Best for: Open processing floors in meat processing, dairy plants, bakeries and general production halls, with the mounting height and spacing set in the calculation, planned the same way as our factory lighting.
lamp4

IP69K LED Tri Proof Light

LED tri proof linear fixtures are sealed against dust and water and built for the conditions inside food processing facilities. These vapor tight luminaires deliver efficacy that depends on the series, with wide beam angles that spread light evenly across work surfaces.

The sealed housing is tested against 100 bar water jets at 80°C, and selected versions have 304 or 316 stainless steel end caps. Most versions use a polycarbonate tube; a borosilicate glass version is offered for areas with strong acids and alkalis, so specify polycarbonate above exposed food unless the plant's glass policy allows a guarded glass fixture. Low flicker drivers are available on selected configurations, and the smooth housing leaves no exposed hardware where dirt can collect.

Best for: Cold storage, refrigerated aisles, processing lines and lower ceilings where even light along the line matters more than raw output. The full LED tri proof lights range adds IP65 models for dry areas and sensor models for corridors.
IP69K LED Tri Proof Light

What to Look for in Food Processing Light Fixtures

Fixtures for food processing serve facility owners who need sanitation compliance and workers who need safe, comfortable lighting. Check the operating temperature range on each model's datasheet, from blast freezers to hot processing lines, and choose polycarbonate versions where the plant's glass and brittle plastic policy applies above exposed food.

Long lasting LED technology means fewer interruptions for lamp changes on production lines. Rated life is stated on each model's datasheet, usually as L70 or L80 with its test conditions; ask for that data and the driver life at your room temperature for the model quoted.
brightness-up (1)

High Performance LED

Upgrade existing HID and fluorescent fixtures with LED luminaires, comparing the measured input of the old fittings with the new ones at the same light on the work surface. Efficacy depends on the model and configuration, and the worked example under Energy Save shows how to estimate the saving.
droplet (1)

Waterproof & Dust Tight

IP69K rated fixtures are dust tight and tested against high pressure, high temperature water jets. The rating covers washdown, not food safety; NSF certification is its own test, model by model, and the certificates GS LIGHT publishes are listed on the certifications page. Water, steam and cleaning chemicals stay out of the sealed housing when glands and connectors are installed correctly.
cloud-rain

Corrosion Resistant

Food processing environments expose light fixtures to acids, salts, ammonia, and cleaning agents that shorten the life of fixtures not built for them. An IP rating does not cover corrosion, so look at the housing material, the gaskets and the fixings, such as stainless steel end caps on selected tri proof versions. Ask which cleaning chemicals the housing and gaskets have been tested against before you specify them.
shield-check

Hygienic Design

Smooth, rounded housings avoid exposed screws and crevices where dust and moisture collect, which makes fixtures easier to clean during routine sanitation. Shatter resistant polycarbonate lenses help protect exposed food if a fixture is struck by equipment, the kind of protection 21 CFR 117.20 asks for wherever food is open.
ripple

Heat dissipation

Die cast aluminum bodies pull heat away from the LED chips, which helps the fixture hold its output in warm or enclosed spaces. Check the model's rated ambient temperature against the air temperature at mounting height in hot areas.
battery-eco

Energy Save

As an illustrative example: replacing 100 metal halide high bays with 150W LED high bays, assuming each old fitting draws 458W in total (a 400W lamp plus its ballast) and the LED layout gives the same light on the work surface, cuts the load by 30.8 kW. At 12 hours a day, 365 days a year (4,380 hours), that is 134,904 kWh, or $16,188.48 a year at $0.12 per kWh. Your figure depends on the measured input of the existing fittings, the operating hours, the tariff and any dimming.

Food Processing Lighting FAQs

What plant managers, contractors and sanitation leads ask before they send a layout.

Certification is model specific: ask for the certificates and test reports that cover the exact model and configuration quoted. Where a project requires NSF, check the NSF listing for that model; NSF/ANSI 2 is the standard commonly used for luminaires in food zones. GS LIGHT's certifications page lists a TÜV CB certificate for its TPE tri proof light and CE (EMC and LVD) documents for its high bay lights. For North American projects, confirm the electrical listing your inspector requires before ordering.

No fixture can guarantee an inspection result, but inspectors and auditors usually check three lighting points: light levels, protection against glass breakage over exposed food, and fixtures that can be cleaned. Light work surfaces to the levels your authority or customer standard sets, use polycarbonate lenses or guarded fixtures over open product, and choose smooth, sealed housings. The certificates for the exact model answer the food zone questions directly.

Yes, with a model rated for the room: check the operating temperature range on the datasheet of the model quoted before it goes into a freezer. GS LIGHT's IP69K high bay product page lists minus 40°C to 55°C, and an LED rated for the room reaches full output when switched on, without the slow cold start of fluorescent tubes.

It depends on the measured input of your existing fittings, the light the new layout must deliver, your operating hours and your tariff. As an illustrative example, 100 metal halide high bays assumed to draw 458W each, replaced with 150W LED high bays giving the same light, save 134,904 kWh a year at 12 hours a day, or $16,188.48 at $0.12 per kWh. LED also removes most lamp changes, so there are fewer line stops for maintenance.

Send Your Inquiry

Send the plant layout and ceiling heights, the areas to light, the washdown method and temperatures, any chemicals or ammonia present, the light levels or standard you must meet, quantities and timing. We reply with suitable fixtures, a product quotation and the available technical documents.

Ready to Start Your Lighting Project?
From architectural lighting solutions to OEM/ODM customization, GS LIGHT helps global partners create reliable LED lighting solutions.
Copyright 2026 GS LIGHT. All Rights Reserved.
Privacy Policy
Terms & Conditions
Sitemap

Send Your Inquiry

gslight-wechat-qr